(→La manipulation) |
(→Questions sans réponses) |
||
Ligne 33 : | Ligne 33 : | ||
==='''De manière simple'''=== | ==='''De manière simple'''=== | ||
La pression du doigt fait varier la tension dans la surface conductrice. Cette variation est détectée par l'arduino, qui allume alors la LED et déclenche le buzzer. | La pression du doigt fait varier la tension dans la surface conductrice. Cette variation est détectée par l'arduino, qui allume alors la LED et déclenche le buzzer. | ||
- | |||
- | |||
- | |||
=== '''Allons plus loin dans l'explication''' === | === '''Allons plus loin dans l'explication''' === |
Sommaire |
Un détecteur capacitif permet de détecter une pression sur une surface conductrice d'électricité.
Sur une feuille de papier, dessiner des touches au crayon gris en insistant bien afin que le graphite se dépose convenablement sur le papier. Ces traits doivent rejoindre l’extrémité de la feuille. Appuyer ensuite sur les touches.
Lorsqu'on appuie sur la surface conductrice utilisée dans le montage, on peut observer un allumage de la LED et un bruit de buzzer.
La pression du doigt fait varier la tension dans la surface conductrice. Cette variation est détectée par l'arduino, qui allume alors la LED et déclenche le buzzer.
En démarrant le montage, on charge électriquement la surface conductrice pour l'amener à un potentiel. Lorsqu'on touche la surface en question, le corps agit comme une capacité et décharge la plaque, ce qui réduit le potentiel sur la surface.
// Pin a connecter a la LED int LEDPin = 13; // Pin a connecter a la feuille de papier int capSensePin = 2; // This is how high the sensor needs to read in order // to trigger a touch. You'll find this number // by trial and error, or you could take readings at // the start of the program to dynamically calculate this. int touchedCutoff = 60; void setup(){ Serial.begin(9600); // Set up the LED pinMode(LEDPin, OUTPUT); digitalWrite(LEDPin, LOW); } void buzz(int targetPin, long frequency, long length) { long delayValue = 1000000/frequency/2; long numCycles = frequency * length/ 1000; for (long i=0; i < numCycles; i++) { digitalWrite(targetPin,HIGH); delayMicroseconds(delayValue); digitalWrite(targetPin,LOW); delayMicroseconds(delayValue); } } void loop(){ // Si le capateur atteint un certain seuil de tension, la led s'allume if (readCapacitivePin(capSensePin) > touchedCutoff) { digitalWrite(LEDPin, HIGH); // utilisation buzz(4, 2500, 1000); // buzz sur pin 4 à 2500Hz } else { digitalWrite(LEDPin, LOW); } // Affiche toute les 500 millisecondes la valeur du capteur if ( (millis() % 500) == 0){ Serial.print("Capacitive Sensor on Pin 2 reads: "); Serial.println(readCapacitivePin(capSensePin)); } } // readCapacitivePin // Entrée: Arduino pin number // Sortie: Un nombA number, from 0 to 17 expressing // how much capacitance is on the pin // When you touch the pin, or whatever you have // attached to it, the number will get higher // In order for this to work now, // The pin should have a 1+Megaohm resistor pulling // it up to +5v. uint8_t readCapacitivePin(int pinToMeasure){ // This is how you declare a variable which // will hold the PORT, PIN, and DDR registers // on an AVR volatile uint8_t* port; volatile uint8_t* ddr; volatile uint8_t* pin; // Here we translate the input pin number from // Arduino pin number to the AVR PORT, PIN, DDR, // and which bit of those registers we care about. byte bitmask; if ((pinToMeasure >= 0) && (pinToMeasure <= 7)){ port = &PORTD; ddr = &DDRD; bitmask = 1 << pinToMeasure; pin = &PIND; } if ((pinToMeasure > 7) && (pinToMeasure <= 13)){ port = &PORTB; ddr = &DDRB; bitmask = 1 << (pinToMeasure - 8); pin = &PINB; } if ((pinToMeasure > 13) && (pinToMeasure <= 19)){ port = &PORTC; ddr = &DDRC; bitmask = 1 << (pinToMeasure - 13); pin = &PINC; } // Discharge the pin first by setting it low and output *port &= ~(bitmask); *ddr |= bitmask; delay(1); // Make the pin an input WITHOUT the internal pull-up on *ddr &= ~(bitmask); // Now see how long the pin to get pulled up int cycles = 16000; for(int i = 0; i < cycles; i++){ if (*pin & bitmask){ cycles = i; break; } } // Discharge the pin again by setting it low and output // It's important to leave the pins low if you want to // be able to touch more than 1 sensor at a time - if // the sensor is left pulled high, when you touch // two sensors, your body will transfer the charge between // sensors. *port &= ~(bitmask); *ddr |= bitmask; return cycles; }
© Graphisme : Les Petits Débrouillards Grand Ouest (Patrice Guinche - Jessica Romero) | Développement web : Libre Informatique