Grove : capteur de poussiÃ¨re

De Wikidebrouillard.

Version du 22 octobre 2013 à 12:44

Sommaire

1 Introduction
2 Features
3 Application Ideas
4 Cautions
5 Specification
6 Usage
7 Resources
8 Support
9 Crédits

Introduction

This Dust Sensor measures the Particulate Matter level in air by counting the Lo Pulse Occupancy time(LPO time) in given time unit. LPO time is in proportion to PM concentration. This sensor can provide you pretty reliable data for your PM2.5 project or air purifier system because it's still responsive to particulates whose diameter is 1um.

Features

Highly responsive
Reliable
ROHS/PEACH compliant

Note: New version updates output Hi Voltage from Approx. over 4.0V change to Approx over 4.5V.

Application Ideas

Dust emission monitor
Air Quality Monitoring

Cautions

Please keep it upright.
3 min preheat time is required when used at the first time.
Arbitrary operation may cause unexpected damage.
Pins VR1 and VR2 come preset. Please DON'T change the default configuration.

Specification

Items	Min	Norm	Max	Unit
VCC	4.75	-	5.25	V
Standby Current Supply	-	90	-	mA
Detectable range of concentration	-	0~28,000	-	pcs/liter
Operating Temperature Range	0	-	45	°C
Output Method	Negative Logic, Digital output,Hi over 4.0V(Rev.2) Lo: under 0.7V
Detecting the particle diameter	>1 um
Dimensions	59(W) × 45(H) × 22(D) [mm]
Humidity Range	95%rh or less

Usage

Here is a demo to show you how to obtain PM concentration data from this Grove - Dust Sensor.

1. Plug the dust sensor into digital port D8 on the Grove - Base Shield. It can only be D8, because the operation of this sensor involves sampling, a function only can be achieved by D8, the capture input pin of Atmage328P, on Arduino/Seeeduino.

2. Copy and paste the demo code below to a new Arduino sketch.

/* Grove - Dust Sensor Demo v1.0
 Interface to Shinyei Model PPD42NS Particle Sensor
 Program by Christopher Nafis 
 Written April 2012
 
 http://www.seeedstudio.com/depot/grove-dust-sensor-p-1050.html
 http://www.sca-shinyei.com/pdf/PPD42NS.pdf
 
 JST Pin 1 (Black Wire)  => Arduino GND
 JST Pin 3 (Red wire)    => Arduino 5VDC
 JST Pin 4 (Yellow wire) => Arduino Digital Pin 8
 */

int pin = 8;
unsigned long duration;
unsigned long starttime;
unsigned long sampletime_ms = 30000;//sampe 30s ;
unsigned long lowpulseoccupancy = 0;
float ratio = 0;
float concentration = 0;

void setup() {
  Serial.begin(9600);
  pinMode(8,INPUT);
  starttime = millis();//get the current time;
}

void loop() {
  duration = pulseIn(pin, LOW);
  lowpulseoccupancy = lowpulseoccupancy+duration;

  if ((millis()-starttime) > sampletime_ms)//if the sampel time == 30s
  {
    ratio = lowpulseoccupancy/(sampletime_ms*10.0);  // Integer percentage 0=>100
    concentration = 1.1*pow(ratio,3)-3.8*pow(ratio,2)+520*ratio+0.62; // using spec sheet curve
    Serial.print(lowpulseoccupancy);
    Serial.print(",");
    Serial.print(ratio);
    Serial.print(",");
    Serial.println(concentration);
    lowpulseoccupancy = 0;
    starttime = millis();
  }
}

In this program, the seeeduino samples the total duration of "logic low" in 30s, and this duration illustrates the dust density of environment. Open serial monitor, we can read air quality's value detected by sensor from pc serial port.